Greenfield Migweld 200A Gasless Inverter Welding Machine
₱5,900as of Jul 31, 2026
COD · Shopee-protected payment
Greenfield Migweld 200A gasless review: best for MIG
Greenfield Migweld 200A Gasless Inverter Welding MachineDisclosure: Product Choicest is reader-supported. We may earn a commission when you buy through our Shopee links, at no extra cost to you. Learn more.
Our Best for MIG pick: gasless flux-cored welding with no gas bottle to buy, for around ₱5,900, and much easier to learn than stick.
- Price: ₱5,900 as of Jul 31, 2026
- Biggest pro: Gasless MIG needs no gas bottle, so there is no cylinder to buy, refill, or store
- Main catch: Flux-cored wire leaves slag to chip off and spatters more than gas-shielded MIG
At a glance
| Brand | Greenfield |
|---|---|
| Type | Welding machine |
| Price | ₱5,900 (as of Jul 31, 2026) |
| Owner rating | 4.9 ★ from 34 reviews |
| Shop | Greenfield |
| Units sold | 45 |
Specifications
Greenfield does not publish full specs for this model
| Type | Welding machine |
|---|---|
| Process | Gasless MIG (flux-cored), inverter |
| Max output | 200 A |
| Shielding gas | None required, flux-cored wire |
| Duty cycle | Not specified |
| Input | Not specified |
Pros and cons
✓ Pros
- Gasless MIG needs no gas bottle, so there is no cylinder to buy, refill, or store
- Continuous wire feed is far easier to learn than striking a stick arc
- The only non-stick process in this roundup, better on thin sheet and body panels
- Greenfield is a PH brand with real hardware-store distribution
✗ Cons
- Flux-cored wire leaves slag to chip off and spatters more than gas-shielded MIG
- No published duty cycle, so sustained welding time is unknown
- 200A is lower output than the stick machines here, so thick steel is out of scope
- Consumable wire is an ongoing cost that stick rods only partly match
The Greenfield Migweld 200A is our Best for MIG pick: gasless flux-cored welding for around ₱5,900. It is the only non-stick machine in this roundup, and for thin metal it is the right tool.
What does gasless actually mean?
Normal MIG welding needs a gas cylinder to shield the weld pool. Gasless MIG uses flux-cored wire instead: the flux is inside the wire and burns to create the shield.
That removes the single biggest barrier to MIG at home. No bottle to buy, no refills, no cylinder to transport or store, no regulator to set. You plug in and weld.
Why choose MIG over stick?
Because it is much easier, and because of what it can weld.
With stick you strike an arc and then maintain a gap by hand as the rod burns down. With MIG you pull a trigger and wire feeds continuously. Most beginners are laying usable beads far sooner.
More importantly, 200A of MIG suits thin material: sheet metal, car body panels, thin tube, light frames. A 300A stick machine on thin sheet mostly blows holes in it. If your work is bodywork or light gauge, none of the stick machines here are the right answer.
What are the trade-offs?
Three, and they are real.
Slag. Flux-cored wire leaves a coating you have to chip and brush off every pass, and it spatters more than gas-shielded MIG.
Running cost. Flux-cored wire is more expensive per weld than stick electrodes. You save the cylinder and pay for the consumable.
Missing specs. Greenfield publishes no duty cycle and no input requirements for this machine, so sustained welding time is unknown. And at 200A, thick structural steel is out of scope.
Is it sulit?
Around ₱5,900 as of July 31, 2026. Check the latest price on Shopee. It costs more than a 300A stick machine and does less on thick metal, so on raw specs it looks poor value.
Judge it on capability instead. If you weld thin sheet or car panels, it does a job the stick machines cannot, from a Philippine brand with real hardware-store distribution. That is what you are paying for.
Who should buy it
Buy this if you work on car panels, sheet metal, or light frames, or you want the easiest process to learn. Buy a stick machine instead if your work is gates, grilles, and thick steel. See how it ranks in our best welding machines in the Philippines roundup, or browse more on our Home Improvement page. Our welding machine buying guide covers MMA versus MIG in plain words.
Alternatives to consider
For gates, grilles, and general fabrication, the Powerhouse EDGE MMA 300A is our Best Overall at around ₱2,800 with a published 60% duty cycle. If you want maximum power for thick steel, the INGCO 350A/400A ARC welder is around ₱7,600.
Compare Greenfield Migweld 200A Gasless Inverter Welding Machine
See how it stacks up against our top pick in the head-to-head Powerhouse EDGE Inverter Portable Welding Machine MMA 300A vs Greenfield Migweld 200A Gasless Inverter Welding Machine, or browse the full welding machines comparison.
Frequently Asked Questions
What does gasless MIG mean?
The wire has flux inside it, which burns to shield the weld instead of gas from a cylinder. So there is no bottle to buy, refill, transport, or store. The trade is that flux leaves slag you have to chip off, and it spatters more than gas-shielded MIG.
Is MIG easier than stick welding?
Considerably, for most beginners. You pull a trigger and the wire feeds continuously, instead of striking an arc and manually maintaining a gap as the rod burns down. On thin sheet metal the difference is dramatic.
What can 200A weld?
Sheet metal, car body panels, thin tube, brackets, and light frames. It is the right tool for thin material where a 300A stick machine would blow holes. For thick structural steel, a stick welder is the better choice.
Is it cheaper to run than a stick welder?
No. Flux-cored wire costs more per weld than stick electrodes, and it is an ongoing cost. You save the gas cylinder, but the consumable is pricier. Factor that in if you weld a lot.
More welding machines we've tested
Every card links to our full review.
Greenfield Migweld 200A Gasless₱5,900 when last checked
See today's price 🛒